MaxxECU STREET ECU

Description

The MaxxECU brand, has fast become my favourite ECU manufacturer. We install and tune these daily here at the ‘Tuningshed’. I’ve literally spent hours on the dyno, tuning them. We’ve installed countless setups too. The MaxxECU Street is one of our best sellers, as a UK dealer.

We can offer advice on ECU selection, and even with setup and first start. Best of all, we can tune the vehicle for you too.

I’ve started to upload some instructional videos onto my Youtube channel it will give you some idea of what we do, and more importantly, what these products can do for you and your project.

Free with all MaxxECU orders for a limited time, is the PVE ECU Mount kit (Pictured). This will help you make an exceptional job of mounting your new ECU. 🙂

Advanced entry-level engine control system for up to 6 sequential cylinders. Up to 12 in wasted spark

Faster and easier tuning with built-in wideband lambda and a built-in MAP-sensor up to 3 bar / 43.5 psi of boost.

Get started faster with the easy-to-use MTune PC-software

Included within the kit:

MaxxECU Street
3m Flying Harness
USB Cable
Push Lock 4mm Barb
4mm MAP Sensor Pipe
LSU4.2 Lambda Sensor
LSU4.2 Lambda Sensor Connector
Quick Guide
Wiring Diagram
GT150 12 Way connector
Sticker Kit

Selected features:

Aluminium casing
Boost control
Shift-cut
Internal loggings
Flex fuel
Advanced warning system
Built-in wideband lambda
Launch control
Anti-lag

6 injector outputs (high impedance)
6 ignition outputs
4 extra outputs (GPO)
4 extra analog inputs
2 extra digital inputs
CAN bus (additional wires required)

Target engines for MaxxECU STREET

All 1-12 cylinder engines (4-stroke)
Up to 6 cylinders fully sequentially
Up to 12 cylinders in wasted spark

MaxxECU STREET inputs

Intake air temperature sensor (IAT)
Coolant temperature sensor (CLT)
Throttle position sensor (TPS)
Lambda (WBO) sensor. Uses a sensor directly connected to the ECU without any additional electronics. Supports Bosch LSU 4.2, 4.9
2 trigger inputs. VR or digital. Automatic trigger level detection. The signals are processed by a completely separated processor for maximum performance and immunity against interference
2 extra temperature sensors. Can be used as switches or to control additional functions
2 extra 0-5V inputs.
2 extra digital inputs,
Built-in 400kPa MAP-sensor for up to 3bar/43PSI of boost

MaxxECU STREET outputs

6 injectors outputs. High impedance only
6 ignition outputs. 5V signal to drive ignition modules, CDI units or coils
4 outputs for extra features. Can be used to control virtually anything. Fuel pumps, idle control, boost solenoids, nitrous, shift lights, fans, warning lights, etc. GPO 1-3 (2A), GPO 8 (5A)

MaxxECU STREET technical

CAN bus (additional wires required)
USB communication for tuning with MTune
8MB memory for internal logging, up to 1000Hz
Supply voltage 8-22V
ARM Cortex-M3 120MHz main processor
Resolution on ignition: 0.1 degrees
Resolution on injectors: 0.001 ms
Updates the fuel and ignition calculations 2000 times per second
The fastest PC communication on the market
Weight: 520g
140x134x42mm (including mounting points, excluding connector)
Aluminium casing

We normally hold the MaxxECU Street in stock. We aim to deliver next day if ordered by 1pm. However, we normally list up to 14 days delivery in case we run out due to sales. If you would like an exact date of delivery before you order, please feel free to pop us a message, or an E-Mail and we can get back to you ASAP.

MaxxECU ECU Videos